November 19, 2026
Capabilities

From Production Gears to Gearbox Repair

The Adams Company’s sibling brand, Northend Gear & Machine, handles gearbox repair for any make, including OEM gearboxes built with Vector-brand gears.
Northend Gear & Machine team inspecting a rebuilt industrial gearbox in the Ohio shop

Gearbox repair is part of the Vector Companies lineup, thanks to Northend Gear & Machine, a sibling brand of The Adams Company (TAC). Northend has rebuilt industrial gearboxes of any make in Ohio since 1988, and we’re proud to share a platform with that kind of experience.

What an OEM needs from its gears and shafts changes as a design moves toward production. Atlas Gear Company turns out prototype gears fast while the design is still being proven, and TAC machines gears and shafts in production quantities once the design goes to market. For high-volume programs, Atlas Global sources components globally, then inspects and warehouses them in Detroit for scheduled release. Northend takes on the largest parts, hobbing gears up to 72 inches in outside diameter and turning shafts up to 22 inches in diameter and 80 inches long. Whatever the need, there’s a Vector brand with an answer.

‍

One source from gear to gearbox

From there, OEMs build those gears into gearboxes that carry their own name, and their customers put those gearboxes to work in factories, wind farms, and mines. When one of those gearboxes breaks down, the road back to service has often been a long one. Some units go back to the OEM, which may repair them or send them on to an outside shop. Others go straight to a third-party repair shop. Both routes can mean a lot of waiting and plenty of unknowns.

Now that road leads back to Vector Companies. Northend rebuilds any gearbox, including OEM gearboxes built with Vector-brand gears. OEMs and the plants running their equipment get one point of contact they can trust for consistent, transparent, and efficient gearbox repair.

Helical gear and bearing assembly set into a gearbox housing during a Northend rebuild
Northend technician working inside an open industrial gearbox housing during repair

Industrial gearbox repair for plants and OEMs

Most gearboxes reach Northend after a breakdown, when every hour of unplanned downtime counts. Atlas Gear Company is known for turning a replacement gear fast. Northend brings that same urgency to the whole gearbox, with emergency gearbox repair that gets a full unit back in service. If there’s a gearbox sitting on a shelf at your plant waiting for a decision, it might have more years in it than you think.

OEMs gain a rebuild partner too. If your customers send units back for repair, Northend can rebuild them for you.

‍

Inside a Northend rebuild

Every Northend rebuild starts with a complete teardown. The team takes the gearbox down to the last bearing and inspects each component to find the root cause of the failure, reading the wear on every gear for a record of how the unit has been running. Bearings and seals are the most common culprits, followed by leaks and broken gear teeth.

Northend replaces bearings, industrial seals, gaskets, and heavy-duty hardware, then redesigns components where needed so the same failure doesn’t happen again. That might mean swapping a roller bearing for a spherical bearing better suited to how the unit runs.

When a gear or shaft is worn past use or no longer made, Northend reverse-engineers the part, with or without the original drawings, and machines the replacement in-house. Because Northend makes its own gears and shafts, a gearbox rebuild keeps moving without waiting on an outside supplier for parts. Failure analysis and spin testing are available on request.

“Customers bring us all kinds of needs, a prototype gear one week and a gearbox rebuild the next. With Northend, we have an answer for each of them.”
‍
Steve Arthur, President and CEO, Vector Companies

‍

What Northend rebuilds

Brands. Falk, Foote-Jones, Dodge, Sumitomo, SEW-Eurodrive, Link-Belt, Lufkin, Philadelphia Gear, Browning, Nord, and many more

Size. Gearboxes up to 8,000 lb as standard and up to 15,000 lb with crane capacity

Services. Complete teardown and inspection, bearing and seal replacement, gear and shaft replacement, gear remanufacturing, and reverse engineering

Quality. Verified in Northend’s ISO 9001 inspection department

Northend technician inspecting worm gear components on the bench after a gearbox teardown
Gloved hands checking a worn splined shaft against measurements during gearbox repair

Have a gearbox that just went down, or one waiting on a decision? Start the conversation with Northend.